I am all about beautiful and simple decorations for the holidays. Today’s tutorial is how to make a burlap wreath for the holiday season. This is a no-sew, no-glue, no-cut project that should be easy to create in about 30 minutes.
Walmart challenged me to create a DIY decorating project for the holidays and I immediately knew that I wanted to create one of those burlap wreaths that I had seen on so many other blogs. I really wanted to add a festive holiday spin to it, but one that would be easy to execute (and replicate!).
I began searching through blogs for tutorials on how to create my wreath, watched a million YouTube videos, looked at more blogs…and basically my eyes crossed and glazed over. Everyone does their wreaths differently and there is not one magic tutorial, BUT gathering those ideas, this is my version of the burlap wreath with a little holiday spin for you.
2 Rolls of Burlap, 5 inches wide & 10 yards long (here is what I purchased)
18″ wire wreath form
1 package of mini-clothespins
2 floral holiday picks (any variety)
3-5 holiday photos printed in wallet-size
How to Make Your Burlap Wreath
1. To begin, select a few of your favorite holiday photos that can be attached to your wreath. The pictures I picked were from our family’s epic sledding adventure that you we do each year. Send these off to the Walmart Photo Lab and have them printed in wallet-size ($.58 each).
2. Now that you have your photos to decorate your wreath, let’s begin weaving the burlap through our wire wreath form. This is going to take a little time and practice with your first one so don’t get discouraged.
Begin by folding your burlap in half, like I have shown above, and keep wrapping as we go. Select one section of the wire wreath to start in. Feed the beginning end through the wreath as shown above. Over the outer ring, under the next, over the next, and under to finish. Leave a little loose end to tuck in or you can wire it to the wreath with a little floral wire in the back. Now you have started your wreath- super easy! This is the technique we are using throughout. I am showing it to you tightly so you can see how this will work, when you do this, you will be actually pulling out the burlap a bit to give it to that bubble effect that we are going for.
3. Using the working end of the burlap, we are going to begin making the bubbled burlap right next to this row, within the same section of that metal wreath, but we will begin weaving in the opposite direction, continuing to pull out and bubble the burlap as we go, moving the working burlap into each section, weaving one direction than weaving the other direction.
4. When you run out of burlap (it should be when you are about halfway through covering the wreath), tuck the end towards the back and pick up where you left off. Again, you can wire these ends with a little floral wire on the back.
5. Once the entire wreath is covered, secure the final end with floral wire. Finish, by puffing up some of the folded bubbles (if desired) or you can leave them as is, if you prefer a more ruffled, rather than bubbly effect.
6. Finish the wreath by gluing OR wiring two floral picks on the wreath. I just used a little glue, not too excessively like I usually do, so that I can remove these and switch my wreath up with the season (much like my yarn wreath that is STILL gracing my front door). Finish the wreath by attaching a few of your favorite holiday portraits with those mini-clothespins.
Once you are done, here is what the back of my wreath looked like. You can trim any of the pieces down that were wired to help your wreath lay more flush to your door.
Isn’t she lovely? With a little less than $20 supplies and 30 minutes of your time, you truly have a beautiful wreath for your front door, to grace your mantle, or to make a wall in your home more festive. Not to mention, wouldn’t this just make the most fabulous little gift for someone you love for the holidays?
I’m madly in love with it and I hope it inspires you to dress up a door in your home!